Shenzhen Tiancheng Lighting Limited company to welcome you！ National Service Hotline：4008-320-328
| What is the difference between 5050 lamp beads and 3030 lamp beads |
| Time:2022-10-09 00:00:00 | view： |
|
What are the differences between 5050 lamp beads and 3030 lamp beads?1, the packaging size is different: (1), 5050 refers to LED lamp beads with a length and width of 5.0*5.0mm. (2), 3030 refers to the LED lamp beads with 3.0*3.0mm.2. Different colors: (1), 3030 lamp beads are just monochrome. (2), 5050 lamp beads can be two -color, one light two -color and dual -color, good mixed color.3, different power: (1), 3030 lamp beads are 0.2-1W. (2), the power of 5050 lamp beads is still 0.2W-0.5W.One and 5050RGB lamp beads are a type of LED lamp beads. 5050 is named after product size. RGB refers to the three base colors of red, green, and blue light. 2 and 5050RGB lamp beads are: 1. low voltage driver, environmental protection and energy saving. 2. Small volume and easy installation. 3, high brightness, large scattered angle, good consistency.3, EMC3030 is an innovative high -power LED product. Its principles are the same as the EMC3014. They are all light beads made of new materials EMC. 4. Product characteristics are high temperature resistance, long life, and high resistance UV. Five, specific parameters: 1. color temperature: 2870-3220k; 3985-4503k; 5665-6530K.2, Xianxian: 70-75ra. 3, light effect: 105-130LM/W. 4. Light flux: 90-100LM; 100-110LM; 110-120LM. Tiancheng 5050RGB lamps parameters, can be customized, for example, you need to be customized by different brightness, different bands, and different feet. Of course, the specific consulting suppliers are more accurate. 1. [Product Name]: Creee5050RGB Patch LED Lighting Beads 2. [Voltage]: 3.0-3.4V3. [Brightness]: R: 400-500mcd, G: 1000-1500mcd, B: 300-400mcd 6. [Waves]: R: 620-625nm; G: 520-522.5nm; B: 467.5-470Nm 7 . [Make a finger]: na 8. [Life]:\u003e 50,000 hours The main raw materials of the product 1. [Chip]: Kerry/Cree chip2. [Welding wire material]: Dabo pure gold line 3. [glue]: American Dao Corning 4. [fluorescent powder]: Intelsmine beauty 5. [bracket]: the main characteristics and advantages of high -conducting all -copper brackets1. High brightness: The brightness of a single LED patch lamp bead can be as high as: 1200-1500mcd 2. Low attenuation: The company uses the best quality materials for imports, plus the advanced packaging process, the attenuation of the product can be controlled by thousands of points to a thousand points Within the two. 3. Good light consistency4. Life span: The product uses high -quality material packaging, good heat dissipation effect, the product life can be more than 50,000 hours. The highest brightness, the best quality, and the representative of high -end products, but the price is the equivalent of mid -range products, the highest cost -effective product. 6. The red copper bracket (the low -end lamp beads on the market are all iron brackets), 40 yuan silver -plated layer, 99.99%pure gold wire welding The main application of productsBar, soft lamp bar, hard lamp bar, magic lamp bar, etc. The application field is very wide. First of all, the conventional 5050 lamp beads without SK6812 are actually the same The IC controller is added, but the IC controller on the line board does not need to bring IC. What are the benefits of the IC controller to the inside of the lamp beads 1. Each lamp bead has built -in SK6812 controller to achieve pixel -level control 2, SK6812 packaging to the inside of the lamp beads to prevent the IC controller from being trendy Damage 3, built -in SK6812 can avoid the lamp bar that causes the IC pin and the line board to cause failure when bending and twisting 4. The IC controller is built into the inside of the lamp to make the finished line board easier and simple, thereby reducing the fault Rate, improve reliability. 5. Reduce the volume of the finished product and make the application field of SK6812 lamp beads wider. 6, more electrical performance, strong anti -interference. LED patch 5050 indicates the packaging size, what is the unit? 5050LED packaging size: 5mm*5mm*1.6mm, can reach 5500-6000mcd (pure white light, a little less warm light). His working voltage is the same as ordinary LEDs, only 3.2-3.4V, and the current is the same 60mA. Since the volume of the 5050 patch LED is relatively small and the workmanship is relatively fine, it is not convenient to hand -welded, but it does not mean that it cannot be welded. The welding temperature should be controlled within 250 degrees. Essence Since the 5050 patch LED parameter determines that he must be a loved LED, so he is often used in high -end civilian energy -saving lamps, car instrument boards, LED light bands, mobile phone backlight and keys LED products, LED backlight, switch and logo plane backlight, call display, flash, car, audio, indoor display, lighting fixture market. It means that the appearance size is 0.5mm*0.5mm The actual size is 5.3mm*5.0mm5050 refers to the size of 5.0mm*5.0mm 3528 refers There is a specification parameter to go to the official website to learn about it. The plug -in is distinguished by shape, division, ingels, straw hat, patch; patch is distinguished by size, such as: 3528, 5050 represents length and width, the unit millimeter |
